Google Your SEO optimized title page contents

How to Glue Wood Inlay Banding

Learn How to Glue Wood Inlay Banding

 

Learn how to glue up wood inlay banding in the workshop. An important aspect which is critical to the success of the wood inlay banding project is how to glue up and clamp the wood segments. Watch this YouTube video to learn how the woodworker uses a simple step by step woodworking system to ensure an accurate alignment of the wood inlay banding design.

 “A man of knowledge lives by acting, not by thinking about acting. ”

Carlos Castaneda…(1925 – 1998) Peruvian – American author, student of anthropology.

What’s the Best Glue to Use?

 

How to Glue Wood Inlay Banding - Segments for the Diamond PatternThe best glue adhesive based upon my experience for how to glue wood inlay banding is Elmer’s glue all. This white glue has a longer “open time” before it starts to set up. This is very helpful when working with a lot of wood segments and when a woodworker is trying to arrange and secure the pattern of wood inlay banding. This white glue is also a strong wood glue when gluing wood to wood.

 

.

Another Choice for Wood Adhesive

 

How to Glue Wood Inlay Bandings - Diamond Inlay BandingTitebond yellow glue is also a good choice of wood adhesive. Just keep in mind, the woodworker may have figure out how to glue wood quickly. This can depend on factors like temperature, humidity, and the complexity of the wood inlay banding patterns.

 

 

.

An Important Tip & Technique for Gluing Wood Inlay Banding

 

How to Glue Wood Inlay Banding - Painters Tape Secures the Alignment of Wooden SegmentsHere’s a woodworking tip for how to glue wood inlay banding. Clamp a straight board to the laminate surface of the work area. (Remove this straight edge immediately after the wood inlay banding is clamped. Otherwise it could be glued to the project. Keep in mind that blue tape, clear packing tape, or a coating of wax can be applied to the straight edge to protect it from becoming glued.)

The next step is to apply blue painters tape in a manner that will secure the alignment of the wood segments to be first laid down. Use a combination square to create a 90 degree angle with the straight edge of the board and the first segment. Be sure to press the wooden segment down firmly on the blue painters tape. Now it is just a matter of carefully arranging the following segments in place.

 

Be Prepared for the Glue Up

 

How to Glue Wood Inlay Banding - Clamps & a Wood Caul Apply Even PressureWhen learning how to glue wood inlay bandings, it is wise to be prepared. Have the necessary clamps, cauls, wood inlay banding materials, glue, glue brushes, blue tape, glue applicators, and paper towels readily available. Remember, it is always a great idea to perform a “dry run” first just to make sure.

.

 

Work on a Non-Stick Surface

 

How to Glue Wood Inlay Banding - Wooden segments are laid out for a Dry RunWoodworkers will notice that a laminate surface is being used. This type of surface works well during the glue up as it is flat and resistant to the drying glue. It is also easy to clean off any excess glue with a scraper when preparing for the following glue-up.

 

 

 

Related Wood Inlay Banding Articles & Woodworking Videos:

Woodworking How to – Make Diamond Wood Inlay Banding

Wood Inlay Banding – How to Make the Square Pattern

Wood Inlay Banding – How to Make Barber Pole Banding

.

Watch more YouTube woodworking how to videos online.

…Your comments are welcomed…

The Apprentice and The Journeyman University


Woodturning How to Video – Wood Turn a Segmented Knob on a Wood Lathe

Woodturning How To Video – Wood Turn a Segmented Knob

 

Woodturning how to video - segmented woodturning - turned knob with tenonThis woodturning how to video shows how to wood turn a segmented knob on a wood lathe using basic turning tools. In this woodturning project a parting tool, roughing gouge, and spindle gouge with a fingernail grind were used to wood turn the glue up. The woods used for the glue up were hard maple and African mahogany.

Woodturning how to video - segmented woodturning blockThe YouTube woodturning how to video shows a woodturner tightening the segmented glue up into the lathe chuck and then turning a tenon. The tenon is then reversed and tightened within the lathe chuck so that the woodturner can woodturn the main body. Notice how the designs in wood appear as the woodturning takes shape.

 

.

Woodturning how to video - tenonA star pattern of maple emerges in the woodturning how to video as the woodturning project progresses. Watch how the  two laminated woods contrast one another as the woodturner rounds out the knob. Since the star pattern is solid throughout the wooden block, the white tips of the maple star appear as white lines between the arched African mahogany on the outside perimeter of the segmented woodturning.

 

.

Woodturning how to video - Segmented woodturningVarious grits of sandpaper are used to sand and smooth the wooden project of the woodturning how to video. The woodturner starts with 120 grit and progresses to 320 grit wet & dry sandpaper. Afterwards, the woodturning project is nice and smooth to the touch.

 

 

.

Woodturning how to video - Segmented woodturningFinally, the woodturning how to video shows how a wood finish of Tried and True varnish oil finish is applied. The lathe chuck still has a firm grip on the tenon, the wood lathe is turned on, and the finish is a applied using a paper towel. Only a small amount of the oil finish is necessary for a few reasons. The oil varnish simply goes a long way and the segmented woodturning is small. Also, the woodturner wants to avoid any splatter of oil as it is applied to the woodturning project. For this reason it is still a very good idea to work safe and always wear a faceshield during the application of the wood finish.

 

Watch more YouTube woodturning how to videos online.

…Your comments are welcomed…

The Apprentice and The Journeyman University


Segmented Woodturning – a Variety of Ring Sizes.

Segmented Woodturning – Ring Sizes

A variety of ring sizes - segmented woodturning

Some woodworkers wonder how to glue and clamp the rings for segmented woodturning projects. An adjustable hose clamp creates equal pressure for all the segment joints. The above photo shows how adjustable hose clamps are employed as clamping devices for the various sized segmented rings. As you can see some wood rings are stacked to give an idea of the developing shape. All the rings still need to be flattened on one side on the open drum sander.  They will be dimensioned to a parallel and uniform thickness at this time. The rings can then be aligned and glued one ring at a time. Once the yellow glue sets another ring can then be added and glued. It is then just a matter of repeating this process.

Segmented woodturning ring

The segmented rings for this segmented woodturning project will be aligned, stacked, and glued to form a vase. However, this is also the same wood turning procedure that a woodworker would employ to make a segmented bowl. The craft of segmented woodturning is cutting and fitting all these pieces of wood segments and getting tights joints so that a wooden bowl or vase has a basic shape. At least 80% of the work is cutting, fitting, and gluing the various wood segments. Then it is up to the woodturner to mount the piece to the wood lathe and then shape the woodturning project using various turning tools. Then it is a matter of sanding and then finishing the woodworking project to one’s satisfaction.



Recommended Woodturning Videos:

Let’s Turn Salt and Pepper Mills – How to Woodturn

Segmented Wood Turning – Fruit Bowl…part 1

Segmented Woodturning – Fruit Bowl – part 2

Segmented Woodturning – 9″ x 12″ Vase

Finishing the Segmented Vase of walnut & maple

The Apprentice and The Journeyman University

Segmented Woodturning – Gluing and Aligning wood rings

Segmented Wood Turning – Gluing and Aligning Wood Rings

 

Segmented woodturning requires a strategy. When it is time for stacking the segmented rings and applying wood glue, this is especially true.  We want to make sure that the pattern that we are creating is aligned correctly. For beginning woodworkers and experienced woodworkers this can be a challenge at times.

Segmented woodturning - Gluing and aligning segmented rings.Here’s one method that can be used for gluing and aligning wood rings in segmented woodturning. Glue and align a ring to the segmented bowl or vase and apply mild downward pressure using the drill press and the drill press table. The bottom ring is now aligned and the yellow glue is setting up. In this photo you can see the importance of how the vertical spacers of walnut are aligned. Keep in mind that this alignment needs to be accurate all the way around the vase.  In this picture the drill press is used with just enough downward pressure to allow the the yellow glue to get a good bond. Of course, if a craftsman wants to he could also make a clamping device that incorporates a press screw. This will also serve the same purpose.

Spring clamps used for gluing & aligning the wood rings of a segmented woodturning

In the photo to the left, spring clamps are used to secure the gluing and alignment of the wood rings of a segmented woodturning. It is important to spread the glue evenly on the ring surfaces. Be judicious about the amount of glue that is spread using an acid brush  because we want enough glue to create a good bond. Yet, too much glue is not beneficial. Once the glue is distributed, let it become somewhat tacky and then align the rings. Carefully apply the spring clamps for a good even pressure throughout.

Using this gluing and aligning technique allows the woodturner to create many  pairs of rings at once. After the glue of these segmented rings rings is set, the woodturner can begin to glue and align pairs of segmented rings together. This can save the craftsman time during this segmented woodturning process. Note: In many cases, it is not necessary to let the glue setup over night for this operation. Depending on the temperature and humidity in the woodworking shop, the glue may be setup enough within a few hours for the purpose of gluing and aligning. Of course, it is best to let the glue cure overnight. When the glue of the segmented woodturning is completely set, it can then be mounted to the wood lathe for turning.


Watch these Woodturning Videos:

Let’s Turn Salt and Pepper Mills – How to Woodturn

Segmented Wood Turning – Fruit Bowl…part 1

Segmented Woodturning – Fruit Bowl – part 2

Segmented Woodturning – 9″ x 12″ Vase

Related Posts with Thumbnails
'http://c.compete.com/bootstrap/'; s.src = t + __compete_code + '/bootstrap.js'; s.type = 'text/javascript'; s.async = 'async'; if (d) { d.appendChild(s); } }());