Google Your SEO optimized title page contents

June 29, 2017

Wooden Patterns for Parquetry

Creating Wooden Patterns for Parquetry

Small wooden patterns of geometric design can be safely cut on the band saw. This post shares with you a few woodworking ideas that will enable you to create some wonderful parquetry for your wood projects using a bandsaw crosscut sled. The wooden patterns shown are made from hardwoods leftover from various wood projects. It’s a great way to utilize scrap material!

Wooden Patterns for Parquetry - 60 Degree DiamondsThe  lozenges  are diamond segments that are cut using the 60 degree band saw sled. A stop block is set up and clamped to to the sled’s fence to ensure uniform segments. Keep in my that all four lengths of the lozenge must be of equal length. A few test cuts with scrap material measured with a dial caliper will guarantee the correct length. Check that the sides are equal to one another. Another way to check is to measure across the lozenge in both directions. These dimensions are to be equal to one another.

 

Wooden Patterns for Parquetry - 60 Degree Band Saw SledOnce you begin to cut the lozenges, you will start to experiment with various hardwoods. It’s only natural to rearrange the diamond shaped wood segments. You will mix in various wood tones to create a number of wooden patterns. Play with it. Before long you will see 3 dimensional wooden cubes appear.

 

 

Wooden patterns for parquetry - 60 Degree Band Saw SledThe star wooden pattern is a simple matter of having six lozenges. In this case three are of maple while the other three lozenges are walnut. To glue this wood design just brush on the glue with a disposable glue brush, check for alignment, and wrap a rubber band around it to serve as its clamp. Once the glue sets, it will be plenty strong.

 

 Hardwood veneers of these various wooden patterns can be sliced on the band saw using the techniques that are shown to you in the accompanying woodworking video. Just use a longer block of wood and attach double stick tape. Attach the wood pattern to the tape. Set up the Rockler thin rip jig to the desired thickness of the veneer that you want. (3/32″ is my preference.) Adjust the band saw fence and you are ready to slice veneers.

…Your comments are welcomed…

 

The Apprentice and The Journeyman University


35…Woodworking Tip – The Power of the Shim

Woodworking Tip – a Simple Shim

 

“Never underestimate the power of a single thought.”
Ender…Friend and Salesman…(1964-)

Woodworking Tip from a Friend

 

A Crosscut Sled, Table Saw and a Paper shim

A Crosscut Sled, Table Saw and a Paper shim

Have you ever tried to remove a small amount of material for a perfect fit? Sometimes it can be a challenge. Here’s a woodworking tip that just might work for you.

There are times that a little woodworking tip can make all the difference in the world for a woodworker. A small idea can be profound in its simplicity and that is the case with this woodworking tip. It was passed on to me during my apprenticeship by a journeyman whom I had the pleasure of working with for a many years. He has been gone a long time now. However, I am grateful to him for sharing this useful woodworking tip and technique. It is often employed while working in the wood shop. See if you agree.

We as woodworking craftsman continually strive to improve of skills. A woodworking tip can come in handy. In this video a lid for a jewelry box is being fit without a tape measure or carpenter’s ruler. See how to make the cut with the aid of a paper shim along with a crosscut sled on the table saw. Watch and you can see how to make the cut done by “sneaking up” on the crosscut to achieve a perfect fit.

 

Note: Tearout of the lid is eliminated by using the zero clearance crosscut sled.

 

The woodworking tip for the video segment is taken from a 6-part video series…Let’s Build a Jewelry Box.

 

Recommended Video… How to make poorboy Parallel Clamps
………………………………………….


The Apprentice and The Journeyman University

 

Making Wood Inlay on the Bandsaw

When a woodworker searches the web to learn how to make wood inlay bandings there is little information to be found. In fact there seems to be very little information about how the masters of wood inlay created the wonderful patterns that are sometimes seen on museum quality furniture. However, there are some patterns of wood inlay from the Buffard Freres that offer a glimpse into the world of classic wood inlay from Paris. After studying these inlay designs the urge hit me to figure out how to could duplicate some of these patterns. What I am learning of this “lost art” I will attempt to share with those interested.

When I first began making wood inlay bandings my tool of choice was the table saw. However, my work has evolved and now my band saw is getting a workout. I like working with the band saw for cutting wood inlay segments for a number of reasons.
1). I find it safer when working with smaller or narrower wood pieces.
2.) There is no chance of kickback on a band saw.
3.) The band saw offers a great deal of control when working with sleds and the band saw rip fence.

The Band Saw Sleds:

1.) The Bandsaw Crosscut Sled
2.) The Dedicated Band Saw Miter Sled
3.) The Tilting Miter Sled for the Band Saw

Also important…The Bandsaw Rip Fence for Cutting Thin Strips

The three sleds and the rip fence each take 10-15 minutes to make and they can be made from scrap material in the workshop. The sleds are highly accurate and efficient. Actually, I had not seen or heard of any band saw sleds before I thought of cutting wood inlay segments on the band saw. My band saw sleds are an original thought that I developed for the purpose of cutting wood inlay segments. The sleds have opened up a new dimension for my band saw work and it’s as if my band saw has suddenly been upgraded.

When preparing stock for wood inlay it is important that the material is dimensioned properly. The material being used needs to be flat and of uniform thickness. I use the open drum sander for this operation.

When using a sled I clamp a stop block to the fence so that segments are cut to a uniform width or length.

So far the segments for the wood inlay I have created have been cut at either 90 degrees or 45 degrees. For the 90 degree cuts I use the crosscut sled. When making 45 degree cuts I use either the dedicated miter sled or the tilting miter sled depending on the particular cut to be made. Keep in mind is that the bandings do not have exposed end grain. The wood grain shown is either edge grain or face grain.



The Apprentice and The Journeyman University

Creating your own Wood Inlay Bandings…The Secrets Revealed

“I have missed more than 9,000 shots in my career. I have lost almost 300 games. On 26 occasions I have been entrusted to take the game winning shot…and missed. I have failed over and over and over again in my life. And that’s precisely why I succeed.”
Michael Jordan…(1963 – ) Former professional basketball player, active businessman, and majority owner of the Charlotte Bobcats.

Wood inlay has a mystique about it. Some of the finest furniture created by craftsmen have custom and intricate inlay designs that cause onlookers to pay special attention and take a closer look. There are times that a simple stringing of wood inlay can make a lasting impression. Then again there are instances when intricate inlay patterns make one stop to try to figure out how in the world the craftsman ever created such a magnificent design of varying colored woods. The problem that remains for many woodworkers is that there is little information to be found on how to create bandings for wood inlay. Here, we begin our journey in how to craft decorative wood inlay bandings.

Consider this article as a preview. In following articles we are going to take an in depth look at how different wood inlay designs are made. We are going to simplify and set aside the mystique of wood inlay. In the woodworking shop we are going to create wood inlay bandings of unique designs that will adorn furniture, jewelry boxes, picture frames, and more. These articles about creating wood inlay in the shop may pleasantly surprise those who decide to follow along. Get ready to take a closer look at creating your own custom wood inlays.

Note: The following is the cut pattern for “Barber Pole” wood inlay. The Tilting Band Saw Miter Sled is used to cut this pattern. The angles are 45 degrees.

Barber Pole Pattern for wood inlay

The following band saw accessories will be used in creating shop made wood inlay bandings:

Band Saw Rip Fence

Band Saw Crosscut Sled

The Tilting Bandsaw Miter Sled

The Dedicated Bandsaw Miter Sled
…………………………………………………………………………………………………


The Apprentice and The Journeyman University

Related Posts with Thumbnails
'http://c.compete.com/bootstrap/'; s.src = t + __compete_code + '/bootstrap.js'; s.type = 'text/javascript'; s.async = 'async'; if (d) { d.appendChild(s); } }());