Google Your SEO optimized title page contents

February 23, 2017

Steve’s Table Saw Miter Sled

Table Saw Miter Sled – Viewer Built

 

Steve's Table Saw Miter Sled 2A table saw miter sled is one of the most useful table saw accessories that can be made by the woodworker in the workshop. In this woodworking article we will take a look at the table saw miter sled that Steve from Tropical Cairns, Australia built in his well organized woodworking shop.

(Steve learned how to make a sled for by watching and studying our free woodworking video, How to Build a Table Saw Miter Sled. He also accessed our free woodworking plans for the table saw miter sled.)

Notice that Steve is using a very flat plywood as the base for his table saw miter sled. Both the front and rear fences of the miter sled are of straight grained material. This is especially important for the tall fence closest to the woodworker as this section of the table saw sled serves as a cross cut sled. So, it is imperative that this fence is straight across when material is placed along it to be cross cut.

(Based upon the photo it looks like Steve is able to cross cut a board that is 4- 6 inches wide. So, essentially this table saw miter sled design also has the additional capacity of serving as a cross cut sled.)

Steve's Table Saw Miter Sled 1The interior fence system for Steve’s table saw miter sled is comprised of 3/4″ straight grained material that form a balanced 90 degree angle at the saw blade kerf. Theoretically, we want a 45 degree angle to both the left and right sides of the fence. More importantly, we want to ensure miter fence has a perfect right angle so that the sum total of our miter joint equals 90 degrees.

It is also worth noting that Steve has used a sealer for his table saw miter sled. By doing so, Steve who lives in the humid tropics has helped ensure that his miter sled for his 10 inch table saw will remain flat and true.

Note: When using a table saw miter sled for cutting miter joints or making a cross cut, do not be tempted to switch table saw blades.  It is recommended to use the the same type table saw blade as the original blade that was used to cut the sleds zero clearance saw kerf. The zero clearance saw kerf ensures against any wood tear out.

When cutting miter joints what methods do you prefer?

Do you prefer to a miter joint with a miter saw or table saw?

Many woodworkers cut miters with a table saw miter gauge. What is your preference?

 

More Miter Sled Videos:

Mastering the Miter Joint

Let’s Make Spline Miter Joints

Let’s Make Picture Frames with the Tablesaw Miter Sled

Miter Sled Article:

How to Make Perfect Miter Joints

 

Let us know how it your table saw sleds out for you. If you have sled photos that you’d like to share, feel free to contact me.

 

The Apprentice and The Journeyman University


How to Make a Picture Frame – Top Woodworking Tips

Wooden Picture Frame - How to Make a Picture Frame - Top Woodworking TipsHow to make a picture frame: There are probably as many woodworking methods and techniques on how to make a picture frame as there are woodworkers. With that said, this woodworking video and article will focus on a process that simply works very well in my woodworking shop. I think you will enjoy and find these top woodworking tips useful for your woodworking. You will notice that the written article has a step by step approach for how to make a picture frame. As you study the top woodworking tips featured in this woodworking article, you will see that there are also time sequences relating to the video. These times will help you to better understand the events in the video and article. If you are new to woodworking, I encourage you to study this video and article time and time again. There is a lot of basic woodworking techniques used in this process that will help to advance your woodworking skills to a higher level.

Top Woodworking Tips

We are demonstrating: 1.) How to rip our material safely on the tablesaw.  2.) How to make a picture frame moulding detail on the router table. 3.) How to use a dado blade set to create a rabbet and plough on the picture frame moulding. 4.) How to cut our picture frame moulding to a rough length using the crosscut sled on the table saw. 5.) How to make a picture frame with perfect miter joints. We use a miter sled on the tablesaw for this operation. 6.) How to secure our picture frame miter joints accurately and efficiently by using Ulmia spring clamps.

[kkytv id=”zLcDISz8LRI”]

Note: This article and woodworking video is part of a series. The other videos will focus on how to make splines miter joints,  how to create shop-made wood inlay bandings, and how to cut and fit decorative wood inlay banding to the picture frames.

Preparation to Make a Picture Frame

Material Preparation: We determine how many picture frames that are to be created. This in turn dictates how much material we need for our job. In order to make a picture frame we need to work with dimensioned material. 1.) We start with rough mahogany boards that need to be dimensioned. 2.) Surface one side of the mahogany on the jointer. 3.) Run our material through the planer to achieve a 3/4″ uniform thickness.  4.) Joint an edge on each board so that it is straight and square along its length.

How to Make a Picture Frame

The woodworking video begins

Ripping on the Tablesaw

1.) (0:00) Set the width of the desired cut by adjusting the tablesaw fence to the saw blade. 2.) Adjust the saw blade height so that the saw teeth are about 1/4″ or so above the material being ripped. For safety’s sake there is really no need to have the blade any higher. The less the sawblade exposure the better.

Notice:

1.) There is a sharp 10″ table saw blade installed for the cuts to be performed.

2.) The table saw blade is accurately set to 90 degrees by using a Wixey Digital Angle Gauge. Wixey Digital Angle Gauge - How to Make a Picture Frame - Top Woodworking Tips

3.) A zero clearance insert with a splitter is installed on the tablesaw to avoid the possibility of kickback. (0:18) In the video watch how the splitter keeps the saw kerf open. We want an open saw kerf . If the saw kerf closes this could lead to the material binding on the blade causing a potential dangerous situation called kickback.

4.) Eye protection and hearing protection is used by the woodworker while working with the machinery. The dust collector is also on during the machinery stages.

5.) (0:28) An outfeed table for the tablesaw is utilized. The outfeed table allows for ease of working as well as an element of safety.  The woodworker can confidently push the material through the sawblade without the need to reach across either the tablesaw and the spinning saw blade.

6.) (0:44) The Pushstick: Take a look at the type of pushstick used in the video. It has the shape of a shoe. The reason that this push stick is used is to obviously keep the hands of the woodworker away from the blade. This pushstick also guides the material forward while keeping the material flat on the tablesaw. Pay close attention the the feedrate that the woodworker applies. He is simply allowing the table saw blade to cut through the material at a controlled pace.

7.) A clear space on the table surface to the woodworker’s right allows him the to conveniently lay the ripped material. This allows for ease of operation and organization.

The Router Table Setup

A router table insert is used along with a router. 1.) Align the router table fence to the bearing of the router bit with the aid of a straightedge. (In this case a framing square was used.) 2.) Clamp the router fence securely in place. 3.) Adjust the router bit is to a desired height. This preparation is performed using a scrap piece of the picture frame moulding.

Notice:

1.) (1:02) A plastic featherboard is securely in place on the router table a few inches before the router bit. This feather board has two knobs which lock it into position in the metal track. The featherboard is adjusted so that the material is able to ride along the router fence without any lateral movement. This control makes for a straight and uniform moulding cut.

2.) (1:41) A shopmade featherboard is clamped to the router table fence a few inches before the router bit. The maple featherboard keeps the material flat against the router table surface to allow for a straight and uniform moulding profile.

In a nutshell, these featherboards allow for the woodworker’s safety while controlling the shape of the moulding profile. There is something else that is quite important though. By having the featherboards in place, the woodworker is able to work confidently and with piece of mind. He knows he is reducing the margine for error by working safely.

3.) Watch the feedrate of the material as the woodworker takes a pass. Notice the depth of cut compared to the hardness of the material. How much material should be removed in one pass? Too heavy of a cut can create a safety issue or cause the router bit to burn the material. Too light of a cut is unproductive. Remember to make your first pass with a practice cut on a piece of scrap picture frame moulding. Once you are satisfied with this setup, it is just a matter of running the moulding profile on the rest of the material.

4.) (1:47) Notice the pushstick used in the router table operation. It is made from plywood and is about 12″ long. The pushstick is held at an angle to control the material while being guided through the operation. The all important pushstick  allows the woodworker’s hands and fingers to be clear of the spinning router bit.

The Dado Blade Setup

1.) (2:02) Freud Super Dado 8-inch Stack Dado  is used in the dado operation.

2.) (2:10) A shopmade tablesaw insert is used for a zero clearance cut.

3.) (2:10) A shopmade sacrificial Dado Fence is clamped to the Biesemeyer Table Saw Fence.

4.) (2:10) A Dial Caliper accurately measures the depth and width of the rabbet cut.

5.) (2:19) Both featherboards are in place to control for safety and the accuracy of the rabbet.

6.) (3:00) The dado blades and fence are adjusted to create a plough (or groove) on the face of the picture frame moulding. This will be the location for the decorative wood inlay banding. (3:32)

Tablesaw Crosscut Sled

1.) (3:34) The mahogany picture frame moulding is being crosscut to a predetermined rough length. The top and bottom members of the picture frame are shorter than the side members. So, we need 2 separate lengths of picture frame moulding.

2.) (3:58) Notice how the adjustable stopblock on the rail of the crosscut sled is being used. Once the initial moulding member is measured for length, a pencil tic mark is made on the moulding. Place the moulding along the sled’s rail. Now, set the pencil tic mark on the sled’s saw kerf edge closest to the stopblock. (4:05) The next step is to simply slide the adjustable stop block to the square end of the moulding from where the measurement was initiated. Now, all rough cuts will be guaranteed a uniform length. (4:18)

The Tablesaw Miter Sled

1.) a.) (4:27) Prepare for the initial right miter cut of the shorter members of moulding. b.) (4:33) Set the left end of the picture frame moulding  just over the miter saw’s keft. c.) Secure a stopblock by clamping it to the miter sled fence.  d.) Cut all the initial right miter cuts for the shorter lengths of picture frame moulding. Mitre Sled for Table Saw _ How to Make a Picture Frame - Top Woodworking Tips

2.) (5:32) Using the same procedure as above, make all initial right miter cuts for the longer members of moulding.

Determine the Length of each Moulding Member

Long Picture Frame Member: (6:28)

1.) a.) Working from a plan or previously made picture frame, take the measurements from the inside edge of the frame. In the video you’ll notice the woodworker line up a long member of the moulding to match a miter of an existing picture frame. b.) (6:31) Place a pencil tic mark at the short point of the opposite (left) miter. This determines the length of the longer member.

2.) a.) (6:40) Line up the pencil  tic mark with the miter sled’s left edge of the saw kerf. Make sure that the inside edge of the moulding is flush against the miter sled fence. b.) (6:55)  Clamp a stopblock along the miter sled’s fence where the long point of the opposite miter is located.

3.) (7:05) Proceed to trim the left miter.

Short Picture Frame Member: (7:31)

1.) a.) Determine the length of the short picture frame member by laying the miter on the existing picture frame or the plan. b.) (7:39) Along the inside edge of the moulding place a pencil tic mark at the short point of the miter that is to be cut.

2.) a.) (7:51) Place the pencil tic mark on the left edge of the miter sled saw kerf’s edge while making sure the inside edge of the short member is flush against the miter sled fence. b.) (7:58) Secure the stop block to the miter sled fence.

3.) (8:09) Turn the tablesaw on and cut the left miters for all the short members.

Dry Fit the Picture Frame Members:(8:23)

1.) Align each miter joint precisely.Ulmia Spring Pinch Clamp and Miter Joint - How To Make a Picture Frame - Top Woodworking Tips

2.) Secure each miter joint using an Ulmia spring pinch clamp. (The Ulmia miter clamp pliers and the Ulmia miter clamp rings are also featured in the woodworking video.)

Gluing and Clamping the Miter Joints:(8:45)

1.) Brush on white glue to each joint side with an acid brush. Make sure there is enough glue, but not too much. Reach a happy medium.

2.) a.) (8:59) Work on a flat surface while aligning each miter joint. b.) Open the clamp ring and release the pressure to secure the joint. c.) Continue this routine until all 4 joints are aligned properly. (9:35)  Good job!  d.) Proceed to the next picture frame to be assembled. e.) Develop a rhythm to your work and enjoy the process. f.) Place stickers under each picture frame and away from the wet glue during the drying process.

Woodworking Power Tools


The Apprentice and The Journeyman University

Online how to Woodworking Guide – The Apprentice and The Journeyman University

The Apprentice and The Journeyman University

An Online How to Woodworking Guide

Segmented Woodturning - Woodturner - Online how to woodworking Guide- The Apprenticeand The Journeyman UniversityThe Apprentice and The Journeyman University is an Online How To Woodworking Guide  specifically for woodworkers. This ongoing collection of  woodworking videos, articles, and wood projects is for the beginning woodworker as well as the experienced woodworker. The primary goal of sharing this woodworking knowledge base is to pass on experience to those who want to take their woodworking skills to a higher level.

The online how to woodworking guide is set up so that you can easily browse through the various woodworking subjects at a glance.  This offers woodworkers an opportunity learn many new woodworking ideas. These are how to woodworking tips that you can immediately apply in your woodworking shop. So, if you are new to woodworking and have been wanting to learn how to woodwork, take your time and enjoy this knowledge base. If you are an experienced craftsman, here’s an opportunity to share proven woodworking ideas and techniques. If you find value with this online how to woodworking guide, consider The Apprentice and The Journeyman University as a regular source for your online woodworking.

“Simplicity is the ultimate sophistication.”
Leonardo da Vinci 
…Italian painter, sculptor, architect, and engineer…(1452-1519)

Architectural Details…Interior, Frank Lloyd Wright Robie House, Chicago - Frank Lloyd Wright Homes - Online how to Woodworking Guide

Custom Inlay Designs for Arts and Crafts Woodworking

Decorative Door Knockers of Florence, Italy

Decorative Inlay Patterns for Custom Hardwood Inlays

Decorative Woodworking Patterns of Architectural Millwork & Custom Moulding

Fine Woodworking Patterns for the Skilled Woodworker

Frank Lloyd Wright Homes – CarpentryVideo

Front Doors of Florence Italy

Santa Maria del Fiore…Duomo Cathedral of Florence, Italy

Woodworking Ideas & Patterns from Santa Maria del Fiore Duomo

Articles…Segmented woodturning - Wood lathe - new to woodworking - woodworking ideas

Band Saw Woodworking Safety Tips

How Venice Italy was Built on a Foundation of Wood

Miraculous Staircase – Carpentry and WoodworkingVideo

Steve’s Woodworking Shop Tour

The Practice of Woodworking

Wood Veneer Coffee Table by Vincenzo

Woodworking Skills…The Shape of Things to Come

Arts and Crafts…

Gustav Stickley…Father of the American Arts and Crafts MovementVideo

Custom Picture Frame with Hardwood Inlay

Crosscut Sleds…Band Saw Cross Cut Sleds - Bandsaw Crosscut sled - new to woodworking

A French Built Dedicated Miter Sled

Bandsaw Crosscut SledVideo

Building a Dedicated Miter Sled for the tablesawVideo

Dedicated Miter Sled…revisited

Let’s Build a Bandsaw Miter SledVideo

Let’s Build a Dedicated Dado Sled for the Table SawVideo

Let’s Make Picture Frames with the Dedicated Miter SledVideo

SketchUp of the Dedicated Miter Sled for the Tablesaw

Tilting Bandsaw Miter SledVideo

Inspiration…

James Krenov…Legendary Woodworker 1920-2009

Inspiration in Venice, Italy

 Remembering James KrenovVideo

Sam Maloof…woodworking interview…1982Video

Joinery…

Box Joint Fence for the Dado Crosscut SledSplined Mitre Joints - Picture Frame - Joiner - Joinery

Cutting Tenons on a Dado Crosscut SledVideo

How to Make Perfect Miter Joints

Let’s Make Spline Miter JointsVideo

Mastering the Miter JointVideo

The Splined Miter JointVideo

 

 ProjectsKoa Jewelry Box - Veneer - Veneering - wood veneer - wooden jewelry boxes

A Custom Bathroom Wall Cabinet with Raised Panel Doors

A Hand Dovetailed Black Walnut Jewelry Box

A Multidrawer Wall Cabinet for the Workshop

A Woodworking Drill Press Table

Double Bevel Marquetry…a Tulip of Various Woods

How to Make a Picture Frame – Top Woodworking TipsVideo 

Let’s Build a Drill Press TableVideo

Let’s Build a Jewelry Box…Part 1Video

Let’s Build a Jewelry Box…Part 2…Vacuum PressVideo

Let’s Build a Jewelry Box…Part 3Video

Let’s Build a Jewelry Box…Part 4Video

Let’s Build a Jewelry Box…Part 5…WoodturningVideo

Let’s Build a Jewelry Box…Part 6…JoineryVideo

Let’s Build a Magazine CaseVideo

Koa Wood for a Woodworking Project

Techniques…Cutting thin strips - Saw Techniques - Bandsaw Jig - Resaw Band saw

Band Saw Rip Fence made in the ShopVideo

Bandsaw Resawing Method…Article & Video

Creating Picture Frame MouldingVideo

Cutting Thin Strips on the Band SawVideo

Finish Work Methods for an Inlaid Picture FrameArticle & Video

How to adjust for Band Saw Blade DriftVideo

How to Create Dentil MouldingVideo

How to Cut Uniform Thin Strips

Woodworking Tip – The Power of the ShimVideo

Tools…Wooden picture frame - Ulmia Miter Clamps - Miter clamp - Mitre Clamps - Pinch Clamp

A Favorite Tool…The Wixey Digital Angle Gauge

Card Scraper for Wood Inlay Bandings

How to make Poorboy Parallel ClampsVideo

Poorboy Parallel Clamps…questions from a Woodworker

Precision Woodworking Tools…using a Caliper

Sliding Bevel Gauge – Woodworking Layout Tool

The 5 Most Important Power Tools in my Woodworking Shop

Try Anti-Fatigue Mats…your feet will thank you!

Ulmia Miter Clamps and Pinch Clamps

Using Push Sticks for Safe WoodworkingArticle & Video

Zero Clearance Table Saw Inserts

Wood Inlay…Wood Inlay Bandings - How to make Wood Inlays - Making Inlay Banding - Decorative Wood Inlay

A Sicilian Walnut Table with Decorative Wood Inlay Banding

A Step by Step Process…A Banding with Checkers

A Study of Creating Wood Inlay Bandings

Buffard Freres…The 1926 Wood Inlay Banding Catalog

 Buffard Freres wood inlay bandings…1134-1141

Checkered Wood Inlay Bandings

Creating bandings for wood inlayVideo

Creating your own Wood Inlay Bandings…The Secrets Revealed

Hardwood Inlays made in the Woodworking Shop

How to create Barber Pole Wood Inlay Banding

How to Glue Wood Inlay BandingArticle & Video

How to install Wood InlayVideo

How to make Bandings for Wood Inlay…Part 1

How to make Bandings for Wood Inlay…Part 2

How to Make Designs in Wood InlayArticle & Video

How to Make Picture Frames with Wood Inlay

Learn How to Make Wood Inlay BandingsVideo

Let’s Install Wood Inlay BandingsVideo

Making Wood Inlay on the BandsawVideo

Ripping Thin Strips of Wood Inlay on the Band SawVideo

The Art of Wood Inlay BandingArticle

Wolf’s Tooth…a Decorative Wood Inlay Banding

Wolf’s Tooth Banding…a Two for One

Wooden Patterns for ParquetryArticle & Video

Wood Inlay Banding – How to Make Barber Pole BandingVideo

Wood Inlay Banding – How to Make the Square Pattern…Video

Wood Inlay…the Bandings are readyVideo

Wood Inlay…Making a Statement

Wood Patterns for Inlay BandingsArticle & Video

 Woodturning…Salt and Pepper mills - Wood Turning - Woodturning Projects - Wood Lathe - Woodturner

 Creating and Turning Salt and Peppermills

A fascinating woodturning process

Let’s Turn Salt and Pepper MillsVideo

 Wood turning tools used for the Salt and Pepper Mills

 

 …Segmented Wood Turning…Segmented Woodturning - Segmented Bowl Turning - Segmented woodturners - Segmented woodturning videos

 A Salad Bowl set of maple & walnut…part 1

A Salad Bowl set of maple & walnut…part 2

Finishing the Segmented Vase of walnut & mapleVideo

Gluing and Aligning wood rings for Segmented Turnings

Mortising the base of the segmented vaseVideo

9 1/2″ x 12″ Vase…Segmented Woodturning

Organizing the segments and rings

Segmented Vase 9″ x 12″…Mahogany, maple, cherry, & walnut

 Segmented Vase…maple & walnut

Segmented vase of maple, mahogany, and walnut

Segmented Wood Turning…a Cherry and Walnut Bowl

Staved Segmented Woodturning…a Fruit Bowl

The Process of Segmented Woodturning

Turning a Segmented Vase on a Wood Lathe

Woodturning…A Segmented Vase of Walnut and Maple

Woodturning…Dinner Salad Bowls of Mahogany and Walnut

Woodturning… video of the 9″ x 12″ Segmented VaseVideo

Wood Turn a Segmented Knob on a Wood Lathe…Video

Wood Turning…a Segmented Fruit Bowl…part 1Video

 Wood Turning…a Segmented Fruit Bowl…part 2Video

……

Woodworking Power Tools


How to Make Picture Frames with the Table Saw Miter Sled

Picture Frames Made with a Miter Sled

 

“Learning never exhausts the mind.”
Leonardo da Vinci…(1452-1519) Architect, musician, anatomist, inventor, engineer, sculptor, and painter.

Picture Frames made in the Wood Shop

Making picture frames in the woodworking shop is fun especially when we have a system in which to work. In this case we are making the picture frames from picture moulding that was made on the router table and also on the table saw using dado blades. The dado on the moulding will house the decorative wood inlay that we have previously created in the workshop. (It is nearing the Christmas Holidays at the time of this writing and we have quite a few gifts to make.)

Cutting miter joints for picture frames

Cutting miter joints for picture frames

 

Picture Frames made in Production

 The picture frames that we are making have mitered corners so we are using the dedicated miter sled for the table saw. The sled is set up to cut perfect miter joints and this will allow us to go into production mode as we are building 12 picture frames at this time. Each of the picture frames will display pictures that are 5″ x 7″. The picture moulding is of a Peruvian wood called Camala.

 

The System of making Picture Frames

1.) Using the crosscut sled…Crosscut the moulding lengths slightly oversized.

2.) Divide the lengths into two separate piles (if the sides and top/bottom of the frame are unequal.)

3.) Using the dedicated miter sled… Cut a right miter on all moulding members.

4.) Determine the actual length needed for the sides, use a stop block to control the cut length, and cut the opposite miter.

5.) Determine the actual length need for the top/bottom, use a stop block to control the cut length, and cut the opposite miter.

6.) At the workbench… Assemble the frames by fitting, gluing, and using spring clamps to secure the miter joints in place.

 

Having a dedicated miter sled enables us to create wood projects that have miters with dead-on accuracy. Using the above system with the miter sled allows for production work that is quick and efficient. Appreciate the process and enjoy the results!

 


The Apprentice and The Journeyman University

How to Make Perfect Miter Joints

Making Perfect Miter Joints

 

“You have to expect things of yourself before you can do them.”
Michael Jordan…(1963- )Former American professional basketball player, businessman.

There’s something nice about seeing wood joinery that is well done. It’s a if the craftsman is making a statement about his knowledge of the trade, his set of skills, and his pride in craftsmanship. When you see miter  joints that are clean and tight the craftsman is sending a message that he knows what he is doing because he is well practiced and he cares about his craft. It can simply be seen in his work.

It could be said that miter joints are definitely one of the most common joints in woodworking or carpentry. This is a joint that we are taught early on in our apprenticeships because we will be cutting miters throughout our entire career. As an apprentice it sounds simple enough to just cut a left 45 and a right 45 and glue then together to form a 90. If it were so simple then why are there open miter joints? Let’s take a look at how we can make perfect miter joints.

Perfect Miter Joint Technique

 

In this article I will share with you the best method I know to make miter joints in the workshop. My technique for cutting miter joints is using a dedicated miter sled on the table saw. The sled is simple to build and it does not cost much to build it. In fact it can be made within an hour from scrap material in the shop. Once it is built it can serve the craftsman for a long time. The miter sled if built correctly offers unparalleled accuracy. The sled can easily be set up to do production work. With a good miter sled and a sharp saw blade one can cut perfect miter joints for a picture frames that are ready to glue. Simply put the miter sled is a joy to use.

 

Watch this video…Building a dedicated Miter Sled for the tablesaw

As you can see from the photos the woodworker is making quite a few picture frames. (These wood projects are Christmas gifts in the works.) Notice the stop blocks in the pictures. The location of the stop blocks control the lengths for parts of the picture frames and by having these stop blocks in place the woodworker is able to precisely cut uniform lengths repetitively. This allows for production woodworking as all the parts can be cut accurately and efficiently. Once all the lengths are cut it is just a matter of fitting and gluing the miter joints together.

 

Perfect Miter Joints & Ulmia Spring Clamps

 

When it comes to gluing the miter joints I highly recommend using Ulmia spring clamps. These clamps allow you to properly align the miter joint and then secure it. Once clamped the miter joints will not move. Of course there are different size spring clamps for different size miter joints. My spring clamps have been with me for over 30 years and they have clamped a lot of miters. The clamps are truly worth their weight in gold. If you have yet to experience these clamps you will quickly understand when you use them for the first time. When you decide to purchase spring clamps make sure to buy enough because when you go into production mode you will be doing a lot of clamping. Keep in mind that mitering with these clamps goes quickly.

 

Working with a dedicated miter sled and spring clamps is quick, efficient, and accurate. By following this route you will see your skills and miter joints improve. When finished you can also take pride in the craftsmanship of your work for a job well done.

 

A video for mitering smaller material…Let’s Build a Bandsaw Miter Sled



 

The Apprentice and The Journeyman University

 

Related Posts with Thumbnails
'http://c.compete.com/bootstrap/'; s.src = t + __compete_code + '/bootstrap.js'; s.type = 'text/javascript'; s.async = 'async'; if (d) { d.appendChild(s); } }());